Heil Microphones, Accessories and Spare Parts

On this page you will find Heil Microphones:

• Heil PR-781
• Heil Goldline GM-4
• Heil Handimic
• Accessories Heil Mikrophones
• Spare Parts Heil Mikrophones

The Heil Headsets and accessories are on an own page.

Heil PR-781 Desktop Microphone

PR-781

A new highend microphone which has been designed specifically for transceivers like the Icom IC-7800 oder Yaesu FT-DX9000. Bob Heil writes 'it is wonderful on the KENWOOD TS-2000, 850, 870, YAESU FT-1000 Mark V, and all of the ICOM PRO models as well'.
The PR-781 uses a dynamic microphone module from the professional studio series by Heil, which offers a wide frequency response and a high dynamic range. If you already own another microphone stand with shockmount by Heil you can use that with the PR-781 as well.
Additionally required is a connecting cable like the CC-1-XLR-x.

Technical Data

• Heil Sound PR Dynamic Element
• Frequency response 15 - 16000 Hz
• Low weight aluminium membrane
• Output level -55dB
• Impedance 600 Ω
• Steel case with black finish
• Weight approx. 425g

Optionally you might need:

• ein Heil adaptor cable CC-1-XLR-x suitable for your radio
• Microphone support, Shock Mount, PTT etc. see Heil Microphone Accessories

GM-4 Goldline Microphone

A studio microphone by design but this special version is in particular well suited for modern all-band/all-mode transceivers. Requires CC-1 or CH-1 adaptor cable.

Handi Mic

For years, Bob Heil has been working on eliminating the hollow, clamshell sounds of the hand microphone. There is no argument, when you place a high quality microphone element inside a shell, the end result sounds like you are talking from the bottom of a barrel !
Bob designed a very special open sorbothane shock mount that puts the various Heil microphone elements in the open, not encased in a shell. This results in the cleanest, clearest and most articulate hand microphone - EVER ! The low handling noise and exceptional cardiod pattern makes the Handi Mic ideal for mobile or portable use.
All of the HANDI MIC models are shipped with the unique Heil Dash or wall mount, a 5/8" -27 mic clip and a foam windscreen.
Required cable (not included): The Heil CH-1 is a shielded coil cord with 14" of straight section and 15" of coil making it very easy to use unlike most of the coil cords.

Handimic with included accessories

Accessories for Heil Microphones

Cables for PR-780/PR-781

CC-1-XLR-x is used for the HEIL PR-780/781 verwendet. These cables are available with 8 pin round Foster connector for radios by Icom, Kenwood and Yaesu. The radio side has a 6.3mm phone plug connector for a PTT switch. The microphone connector is 3 pin XLR.

CC-1 Cables

CC-1-xxx can be used for all Heil handheld mikes with 4 pin XLR connector (Goldline, HM, Handimic). These cables are available with 8 pin round or modular plug for various rig types (Icom, Kenwood und Yaesu). These cable do have an additional PTT connector (6.3mm phone jack) for a PTT switch.

CH-1 Cables

CH-1-xxx can be used with all Heil handheld mikes with 4 pin XLR connector (Goldline, HM, Handimic). Coil cord approx. 15" coil, 14" straight. These cables are available with 8 pin round or modular plug for various rig types (Icom, Kenwood und Yaesu). The cables with 8 pin round connector have a connector for a PTT foot switch (6.3mm phone jack, like CC-1-xx), the cables with 8 pin modular plug don't have this connector.

Adaptor 8 pin round to RJ-45 modular

This special adapter converts the modular input of several rigs to the familiar 8 pin male Foster plug that will mate with all of our AD-1 adapters and CC-1 Microphone Connecting Cables. The adaptor brings out the Mic audio, Mic Shield Ground, PTT and PTT ground. This interfaces perfectly with our HMM-Y hand microphone, CC-1Y connecting cables for the HM-10 or Goldline microphones as well as the AD-1 Y adapters for the BM-10, PRO-SET or PRO-SET PLUS! headsets, or any of the Heil headsets.

Heil CB-1-PTT Microphone stand

CB-1-PTT

Heavy microphone base not only for the PR-781. Includes PTT key and cable with 6.3mm connector, fits directly to adaptors AD-1-xx and CC-1-xx-.

Desk stand

Heavy desk stand for HM-10 series, dia. 100mm. Solid die cast base, bottom side with rubber pads.
Second source, because HEIL TB-1 is discontinued

Desk stand

Height adjustable microphone desk stand (210-360mm), base isolated against noise, diameter 160mm. Threads 5/8" and 3/8".

PL-2T

Mikrophone boom for all Heil microphones. Can be installed with supplied clamp on desk or sideboard. Rotates 360°. Picture shows PL-2T with GM-5 (not included) and SM-1 (not included).

HB-1

HB-1

The Heil HB-1 is an articulated arm built of very substantial steel channel structure and balanced by four external springs. It is capable of supporting microphones up to 1.3 kg. The boom moves freely and quietly. It is the perfect for Podcast, Amateur Radio and Commercial Radio studios. The HB-1 is shipped with a standard brass lined 'C' clamp mount with a 50mm span width. The channel is designed so a small diameter microphone cable can be hidden and connectors soldered to each end. The HB-1 Boom accepts all of the standard 5/8" -27 threaded microphone clips on to the chrome stem. (The PR-781 microphone shown above is not included).

SB-2

Short boom
For situations where the PL-2 boom is too large... with clamp for mounting on a table or board. Length adjustable between 30 and 52cm, with cable feed.

PL-3

Microphone boom
Microphone boom with heavy desktop base.
Variable boom (length 470mm). Adjustable height: 210-410mm, mount has 5/8" and 3/8" threads.

SM-1

SM-1 Shock Mount Assembly
Can be used on all booms or stands. Professional shock mount is a unique design. The mic clip is suspended from 8 points using a neoprene elastic cord assembly, suspending the microphone from a direct mount, thus isolating the low frequency acoustical coupling to your desk. Picture shows SM-1 at PL-2T (not included) with GM-5 (not included).

SM-2B

Shock mount for microphones
Can be used on all booms or stands. Professional shock mount is a unique design. The mic clip is suspended from 8 points using a neoprene elastic cord assembly, suspending the microphone from a direct mount, thus isolating the low frequency acoustical coupling to your desk. Suitable for PR-30, PR-40, PR-780, PR-781.

FS-50

Footswitch (noname, not by Heil) with rubber coating, includes cable and plug, suitable for all AD-1 and CC-1 adaptors.

FS-2

Large foot switch, two different keying ports, one closes earlier than the other.

HS-2

The Heil 'Magnum' Hand-Switch PTT
Ergonomically correct, it's shape fits the hand naturally and comfortably, activating just like a pistol trigger.

HS-2 Features:

• Ergonomic design
• Very light touch trigger switch
• Terminates into a 1/4" phone plug which connects into the Heil AD-1 or CC-1 cables.
• Using a very reliable 15 amp MicroSwitch
• Chrome spring cable grommet (just like you Mom's old iron!)

Spare Parts for HM-10 and GM-4/5 Microphone

	Microphone clip Order No. HM-10CLIP for HM-10 and GM-x 9.80 € Buy now
	Wind screen Order No. HM-10WS-GM for HM-10 and GM-x 10.30 € Buy now